Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early Color Television

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 03-04-2017, 03:40 PM
VA561's Avatar
VA561 VA561 is offline
VideoKarma Member
 
Join Date: Apr 2010
Location: norfolk,virginia
Posts: 210
High Voltage problem

This thread relates to the previous vertical centering thread. A'64 zenith console, chassis 25LC20QS. The hv should be 25K. With the brightness all the way down, I am getting 16K at the crt anode. When I turn the brightness up to a normal viewing level it drops down to 12K. The voltage regulator is a 6BK4 and the h.v. rectifier is a 3AT2. I am not able to check either tube on my tube tester. The hv adjustment on the back of the chassis is turned up as far as it will go. I currently have about a 1/2" gap at the bottom of the screen. When the brightness control is turned up to a certain point, the picture gets out of focus. Advice needed as to what steps need to be taken and in what order. Thanks in advance.
Attached Images
File Type: jpg hv1.jpg (64.5 KB, 28 views)
File Type: jpg sam1.jpg (51.5 KB, 51 views)
File Type: jpg gap1.jpg (44.6 KB, 40 views)
Reply With Quote
  #2  
Old 03-04-2017, 04:10 PM
teevee's Avatar
teevee teevee is offline
VideoKarma Member
 
Join Date: Feb 2011
Posts: 103
The oldtimers would recommend checking the cathode current on the 6BK4, there may be provision to do this. I have seen the recommendation of taking the plate connection off of the 6BK4 and (briefly) trying the set to see if the HV comes up. Bias on the regulator tube should be about 15V cathode to grid.
Reply With Quote
  #3  
Old 03-04-2017, 04:10 PM
N2IXK's Avatar
N2IXK N2IXK is offline
Technohippie
 
Join Date: Apr 2011
Location: Sittin' on the "Group W" bench...
Posts: 799
A few checks that you can make to eliminate the most common causes of low HV:

Check the horizontal output, damper, and oscillator tubes.

Check the HV rectifier and regulator tubes by substitution.

Verify that you have proper drive to the HO tube grid, proper screen voltage, and proper cathode current.

Check the DC resistance of the flyback HV winding.

Look for leaky caps, deteriorated coils or off-value resistors in the horizontal sweep stages.
Reply With Quote
  #4  
Old 03-04-2017, 04:15 PM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,832
.....and check the B+ sources to the Horiz oscillator, and to the fly. So many times it's not a tube, but the power supply to the tube....

The 1K ohm resistor in the cathode circuit of the 6BK4 will allow you to measure the regulator current - Sams has the procedure.
__________________
Brian
USN RET (Avionics / Cal)
CET- Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!
Reply With Quote
  #5  
Old 03-04-2017, 05:37 PM
andy andy is offline
VideoKarma Member
 
Join Date: Jul 2002
Posts: 4,004
...

Last edited by andy; 11-18-2021 at 05:06 PM.
Reply With Quote
Audiokarma
  #6  
Old 03-04-2017, 06:10 PM
VA561's Avatar
VA561 VA561 is offline
VideoKarma Member
 
Join Date: Apr 2010
Location: norfolk,virginia
Posts: 210
[QUOTE=andy;3179849]Does the HV adjustment have any effect? There are two general causes of low HV. Either the flyback isn't outputting enough voltage (a bad HV rectifier could also cause this), or it's being loaded down by the regulator.

The HV adjustment has little to no effect. A strange thing, I can't get the screen to go black. The picture I posted of a blank screen was with the brightness turned all the way down.
Reply With Quote
  #7  
Old 03-04-2017, 06:23 PM
andy andy is offline
VideoKarma Member
 
Join Date: Jul 2002
Posts: 4,004
...

Last edited by andy; 11-18-2021 at 05:06 PM.
Reply With Quote
  #8  
Old 03-04-2017, 06:45 PM
VA561's Avatar
VA561 VA561 is offline
VideoKarma Member
 
Join Date: Apr 2010
Location: norfolk,virginia
Posts: 210
Just ordered n.o.s. 6BK4A-B and 3AT2 tubes. Is it ok to use a 6BK4A-B in place of the 6BK4?
Reply With Quote
  #9  
Old 03-04-2017, 06:51 PM
N2IXK's Avatar
N2IXK N2IXK is offline
Technohippie
 
Join Date: Apr 2011
Location: Sittin' on the "Group W" bench...
Posts: 799
Quote:
Originally Posted by VA561 View Post
Just ordered n.o.s. 6BK4A-B and 3AT2 tubes. Is it ok to use a 6BK4A-B in place of the 6BK4?
Yes, but the 6BK4C is the preferred type, with the best X-ray shielding.
Reply With Quote
  #10  
Old 03-04-2017, 07:03 PM
VA561's Avatar
VA561 VA561 is offline
VideoKarma Member
 
Join Date: Apr 2010
Location: norfolk,virginia
Posts: 210
Tried pulling the crt cap off as suggested by Andy. Voltage at the crt anode with cap off, 25K.
Reply With Quote
Audiokarma
  #11  
Old 03-04-2017, 07:24 PM
timmy's Avatar
timmy timmy is offline
VideoKarma Member
 
Join Date: Jan 2011
Location: ferndale ny
Posts: 3,504
Also check the 2- I think they are 1.5 meg resistors off the hv adjust pot they should be matched or at least close. I had the same problem and it wound up being a dogbone cap in the IF strip that had carbonized and rendered the 6bk4 tube useless because the heater for the hv reg tube and the crt and the tube where the bad cap was was bleeding in because it was shorted and the 6bk4 would not regulate. Took along time to find this unusual problem.
Reply With Quote
  #12  
Old 03-04-2017, 08:43 PM
miniman82's Avatar
miniman82 miniman82 is offline
First Light: 1952-2011
 
Join Date: Jun 2009
Location: Great Mills, MD
Posts: 4,159
You have 6BK4 grid issues, probably caused by the bleeder resistors like Timmy said. My Silvertone had a similar issue, the anode got dragged all the way down to 9kv.
__________________
Evolution...
Reply With Quote
  #13  
Old 03-04-2017, 10:04 PM
VA561's Avatar
VA561 VA561 is offline
VideoKarma Member
 
Join Date: Apr 2010
Location: norfolk,virginia
Posts: 210
Smile

Nick don't you miss it here in Norfolk? You could drop by here and perform surgery on the Zenith!
Reply With Quote
  #14  
Old 03-05-2017, 05:25 AM
Username1's Avatar
Username1 Username1 is offline
Not sure how I got here.
 
Join Date: Dec 2009
Location: Orange County NY
Posts: 3,584
before you replace stuff, remove the 6BK4, run the set, if HV
goes up, the problem is in the HV Reg. circuit. And most
likely not the tube....

You might have to just remove the cap off the tube.
Be sure to keep it away from arc to ground
potential.

.
__________________
Yes you can call me "Squirrel boy"

Last edited by Username1; 03-05-2017 at 06:19 AM.
Reply With Quote
  #15  
Old 03-05-2017, 09:06 AM
VA561's Avatar
VA561 VA561 is offline
VideoKarma Member
 
Join Date: Apr 2010
Location: norfolk,virginia
Posts: 210
What does it mean when I am getting a full 25Kv at the crt anode when I unplug the crt cap first?
Reply With Quote
Audiokarma
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:34 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.