Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Diagnostic & Test Equipment

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 12-13-2010, 01:33 AM
a_tubesupply's Avatar
a_tubesupply a_tubesupply is offline
antiquetubesupply
 
Join Date: Dec 2010
Location: Hillsboro, Oregon, west of Portland
Posts: 5
Tube Tester - Calibration? What does it mean? How should I know when it needs done?

Hi, I have three different tube testers, 1) Eico 666, bought as-is, works (un calibratied - I believe) 2) Heathkit TC-1, same story... 3) B & K 606 Dyna Jet, same story.

They all appear to be working fine for me, but when I have tested, a 12AX7 tube, on both the Eico, and the Heathkit the tube tested ok, but when I sent the tube to some one else, they tested on a Hickok TV 7, and told me the tub e was a reject, below emmissions level for acceptable. Why??

They tell me I should get my tube tester calibrated... Is this necessary??

What does this entail/mean?

Is any of these tube testers, (Eico 666, or the Heathkit TC-1 ) well thought of in the High end Tube (audio) world as a good tube tester?
Thanks
Reply With Quote
  #2  
Old 12-13-2010, 09:36 AM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,832
Most emission-only testers have limited means of calibration. The Heathkit and Eico probably have some alignment instructions in the assembly manual. The B&K has an adjustment procedure for alignment - not sure of the details, but one of my B&K's required a "select at test" resistor.

The TV-7, and most Hickok testers are mutual conductance testers, and are calibrated in micro or milli-mhos. The calibration often is by a precision resistance, a voltage, or a "standard" tube. Each calibration procedure is different - I've only calibrated TV-7D/U's (while I was a Navy calibration technician) and one B&K 747 tester, both conductance testers. The 747 calibration put many known-good tubes in the questionable or bad category, so even calibration doesn't assure an accurate test.

There are some "purists" out there that insist that their tubes only be checked on a Hickok tester. The real world is the best tester of all. Many here have seen it - a tube that checks great on the tester, but fails in the circuit (RCA 3.58 MHz oscillator or burst amplifier, anyone??) All too often, you'll see eBay sellers touting tubes that read "110" or some other meaningless number. Worse yet is the "matching" of tubes on a tester. The real world circuits have different bias and plate voltages, different impedances, and different frequency characteristics, so the tube tester matching is often irrelevant.

Just my 2c. Over on AK you'll probably get a whole dollars worth of answers.

Cheers,
__________________
Brian
USN RET (Avionics / Cal)
CET- Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:09 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.