Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #31  
Old 01-12-2018, 06:49 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,541
Please don't mess with video alignment without first checking for plate and screen voltage on the IF tubes, and that their heaters are lit.

The set uses intercarrier sound. So you'd think that with a dead video IF stage, it'd kill the sound too. But since the sound carrier is FM, it could be going through by capacitive coupling.
Reply With Quote
  #32  
Old 01-12-2018, 07:19 PM
Crist Rigott Crist Rigott is offline
VideoKarma Member
 
Join Date: Oct 2015
Location: Waxahachie, TX
Posts: 1,506
Quote:
Originally Posted by old_coot88 View Post
Please don't mess with video alignment without first checking for plate and screen voltage on the IF tubes, and that their heaters are lit.

The set uses intercarrier sound. So you'd think that with a dead video IF stage, it'd kill the sound too. But since the sound carrier is FM, it could be going through by capacitive coupling.
Fair enough. I'll check those voltages.
Reply With Quote
  #33  
Old 01-12-2018, 08:07 PM
Crist Rigott Crist Rigott is offline
VideoKarma Member
 
Join Date: Oct 2015
Location: Waxahachie, TX
Posts: 1,506
OK, here's what I measured. There was no signal to the antenna terminals.

Also the "mains" was only at 114VAC. Hence the low voltage on the heaters and B+ was only 237V. When the mains was brought up to house voltage of 124VAC, the heaters went up to 6vac and B+ went to 257V.

Reply With Quote
  #34  
Old 01-12-2018, 08:46 PM
jr_tech's Avatar
jr_tech jr_tech is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 4,510
Got to get some plate voltage to pin 2 of the 6J6 for openers...perhaps the 15 k resistor in A4 is open?

jr
Reply With Quote
  #35  
Old 01-13-2018, 11:25 AM
Crist Rigott Crist Rigott is offline
VideoKarma Member
 
Join Date: Oct 2015
Location: Waxahachie, TX
Posts: 1,506
Quote:
Originally Posted by jr_tech View Post
Got to get some plate voltage to pin 2 of the 6J6 for openers...perhaps the 15 k resistor in A4 is open?

jr
Yeah, I agree. I checked that resistor. It ohmed out to 21K. I'll pull A4 and replace that resistor too.

I went through the tuner last night in great detail. No problems found except that resistor.
I have another tuner and I'll clip lead the tuner in and try it then swap tuners and try it again.
Then go on to an alignment.
Reply With Quote
Audiokarma
  #36  
Old 01-13-2018, 12:53 PM
jr_tech's Avatar
jr_tech jr_tech is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 4,510
If it has only increased to 21K, I doubt that the voltage would drop that much (75 to 8.2 volts)... is the 6J6 ok?

jr
Reply With Quote
  #37  
Old 01-13-2018, 01:02 PM
Crist Rigott Crist Rigott is offline
VideoKarma Member
 
Join Date: Oct 2015
Location: Waxahachie, TX
Posts: 1,506
Quote:
Originally Posted by jr_tech View Post
If it has only increased to 21K, I doubt that the voltage would drop that much (75 to 8.2 volts)... is the 6J6 ok?

jr
Yeah, I agree. I'll swap out the 6J6 next time.
Reply With Quote
  #38  
Old 01-13-2018, 01:06 PM
Crist Rigott Crist Rigott is offline
VideoKarma Member
 
Join Date: Oct 2015
Location: Waxahachie, TX
Posts: 1,506
I pulled A4 1st IF transformer off the tuner to replaced the 15K resistor. It consists of the 15K resistor, a coil, and 2 mica caps at 10pf and 130pf.

Here is what it looks like:



I was expecting some "real" mica caps. Now I'm concerned that those caps could develop silver mica disease. I'm having some real trouble getting a cap reading on each of those with my cap checker. I could cut them in half and install real mica caps.

What do you think?

Last edited by Crist Rigott; 01-13-2018 at 01:10 PM.
Reply With Quote
  #39  
Old 01-13-2018, 03:36 PM
jr_tech's Avatar
jr_tech jr_tech is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 4,510
Is the 10 pf leaky to ground? that could pull down the plate supply to the 6J6. Otherwise, I think that I would leave them alone, and try to figure out the reason the 6J6 plate voltage is so low first.

jr
Reply With Quote
  #40  
Old 01-13-2018, 03:55 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,541
With the 6J6 removed, check the voltage at pin 2 (plate), and see if it still lugs down.

Dittos to jr_tech on leaving the caps alone unless one is leaky/shorted. Their values are for bandpass-shaping so are fairly critical.

Last edited by old_coot88; 01-13-2018 at 04:04 PM.
Reply With Quote
Audiokarma
  #41  
Old 01-13-2018, 07:58 PM
Crist Rigott Crist Rigott is offline
VideoKarma Member
 
Join Date: Oct 2015
Location: Waxahachie, TX
Posts: 1,506
Quote:
Originally Posted by old_coot88 View Post
With the 6J6 removed, check the voltage at pin 2 (plate), and see if it still lugs down.

Dittos to jr_tech on leaving the caps alone unless one is leaky/shorted. Their values are for bandpass-shaping so are fairly critical.
I checked the voltages on V1 and V2 with the tubes removed.
Reply With Quote
  #42  
Old 01-13-2018, 08:04 PM
Crist Rigott Crist Rigott is offline
VideoKarma Member
 
Join Date: Oct 2015
Location: Waxahachie, TX
Posts: 1,506
Well Late this afternoon I decided to replace the mica caps in A4. I thought that while I had it out, why take the chance. I replaced them with 500V 5% micas. I had the 10pf but didn't have the 130pf so I put 2 in parallel. When I checked them with my cap checker I got 129pf. Good enough. And I also changed out the 15K resistor which read 23K once removed. BTW, all the caps in the tuner were replaced using carbon film caps.



I re-installed the tuner and I now have a much better picture.



On to the alignment.
Reply With Quote
  #43  
Old 01-13-2018, 08:26 PM
jr_tech's Avatar
jr_tech jr_tech is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 4,510
Excellent! did the plate voltage on the 2 6J6 plates change?

jr
Reply With Quote
  #44  
Old 01-13-2018, 08:30 PM
Crist Rigott Crist Rigott is offline
VideoKarma Member
 
Join Date: Oct 2015
Location: Waxahachie, TX
Posts: 1,506
Quote:
Originally Posted by jr_tech View Post
Excellent! did the plate voltage on the 2 6J6 plates change?

jr
I haven't checked it. I'll do that and report back.
Reply With Quote
  #45  
Old 01-13-2018, 08:52 PM
Crist Rigott Crist Rigott is offline
VideoKarma Member
 
Join Date: Oct 2015
Location: Waxahachie, TX
Posts: 1,506
Yeah, I have 137V at pins 1 and 2 of V2 the 6J6.
Reply With Quote
Audiokarma
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:56 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.