|
#1
|
||||
|
||||
Display crosshatch on screen loosen yoke bracket rotate yoke while looking at screen for straightness tighten bracket when straight.... easy peasy lemon squeezy.
10-13" tube Zeniths are VERY SERVICEABLE you just need to figure out how to get them apart and get used to the difference in layout...compare one to a cheap GE or 5 and you'll appreciate the Zenith.
__________________
Tom C. Zenith: The quality stays in EVEN after the name falls off! What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4 |
#2
|
||||
|
||||
Fear not the 13" !! I would rather do them all day than anything else.
SO easy & its on the bench instead of getting up & down. As far as the B&W console goes a better set was NEVER built. They are almost immortal. The only weak spot on them was the audio could be buzzy & hard to tame. That was common to most Zenith tube sets. 73 Zeno LFOD ! |
#3
|
|||
|
|||
Quote:
|
#4
|
||||
|
||||
I've never seen it hard to do in a Zenith TV. I've seen a lot of Zeniths, but I've not seen everything. Usually, they make it easy in portables assuming you've sufficiently separated cabinet and chassis. Worst cases I've seen in other American sets is you have to remove a thing or two on the chassis to get at a can. If it is stumping you then, by all means, post some pics of the area, and one of us will probably remember a trick or figure it out from looking...We are here to help.
__________________
Tom C. Zenith: The quality stays in EVEN after the name falls off! What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4 |
#5
|
||||
|
||||
Assuming its a 13GC10 or later HC, JC, KC, LC..........
Remove two 1/4" screws in top corners of chassis. There may also be also one or two along the sides. Now the chassis will tilt down. The can is behind on the sub-chassis. MOST were mounted on a small steel plate held by a 1/4" to the steel sub-chassis. Remove the bolt & it flips out and its easy to change. If you need more room pull the four 1/4" under the set & the chassis will come out. Take your time so you dont damage the CRT board or pull any wires. At that point everything unplugs if needed. Zenith always put serviceability on top. The only mistakes I remember were the dial lamps & cans in the hybrid sets. They actually took a few minutes to change ! 73 Zeno LFOD ! |
Audiokarma |
#6
|
|||
|
|||
Quote:
|
#7
|
||||
|
||||
1.) Were these bare metal cans with the outer metal shell attached directly to the chassis? If yes then all chassis ground points should be valid negative terminals for the new caps. If no then I assume the originals had a cardboard sleeve and the 3-4 negative mounting ears did not connect to chassis but instead connected to an insulating wafer that is riveted to the chassis in two places...Those have a separate negative lead (or several if used as a terminal strip for the neg bus) going to their outside terminal(s)...You MUST connect the new caps' negative leads to the SAME negative bus wire as their can is on.
Some sets only chassis grounded their caps, some only used the floating negative bus, some did both, some had the negatives on different caps on different busses...It depended on how complex the power supply was. Make sure the replacements negatives are on the same negative as the originals. 2.) sometimes the outer paper/cellophane/plastic layer peels. If the winding has not shorted or shorted to the core all should be fine...Albeit less pretty. Look it over maybe ohm it out...If it is fishy you should notice. Stress a bit, but not too much. We all goof up something, often in the power supply, at least once...Having a variac helps reduce damage risk on first power up.
__________________
Tom C. Zenith: The quality stays in EVEN after the name falls off! What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4 |
#8
|
|||
|
|||
Quote:
|
#9
|
||||
|
||||
Those are the two types I was describing. It sure looks like your in the clear. Good luck.
I've been known on sets where the can area is cramped and the negative is chassis (or the negative line is convenient) to move the new lytic elsewhere on the positive line to a place with more room like what you describe...What you are doing is a valid and logical layout change.
__________________
Tom C. Zenith: The quality stays in EVEN after the name falls off! What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4 |
#10
|
|||
|
|||
Quote:
|
Audiokarma |
#11
|
|||
|
|||
I just want to bring this thread back up for a second. Someone earlier mentioned arcing and the gunk on the crt near the hv connector. I did skip this step but I think it would be good to clean due to some obvious symptoms. I do remember I had a tough time cleaning it. Any tips as far as cleaners or techniques or do I just use a dry cloth and muscle it off? It may sound silly but I couldn't clean it well last time the back of the set was off.
|
#12
|
||||
|
||||
Rubbing alcohol is my favorite for the area around the NV connection on the crt, follow up with glass cleaner for a good shine. Remember there is a black aquadag coating as close as 2" to the HV connection. The dag needs to be there the dirt not so much...Telling them apart takes experience.
__________________
Tom C. Zenith: The quality stays in EVEN after the name falls off! What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4 |
#13
|
|||
|
|||
Quote:
|
#14
|
||||
|
||||
Quote:
Slip Plate was under 15$ on wallmarts website last I checked...it makes a great dag substitute.
__________________
Tom C. Zenith: The quality stays in EVEN after the name falls off! What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4 |
#15
|
||||
|
||||
Quote:
|
Audiokarma |
|
|