Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 09-12-2017, 06:48 PM
Radiophile2001's Avatar
Radiophile2001 Radiophile2001 is offline
VideoKarma Member
 
Join Date: Jun 2006
Location: Montclair, VA
Posts: 105
1967 Color Sylvania video died (Mod. CF16W)

Hi--

I probably do not run my TVs enough...turned them on today and came back down in an hour or so and the Sylvania's raster was out. Opened the can and found some evidence of smoke. Seemed to center around 3CU3A tube, which I removed.

Nothing melted...a resistor(?) was blackened a bit but not melted.

Is it possible that if I just get a new 3CU3A and plug it in, this might come back to life? Cheap on ebay.

Screen was fine when I turned it on today initially, but I left the room. Was viewing via UHF mini transmitter attached to cable box.

Thx!
Attached Images
File Type: jpg IMG_2633.jpg (96.3 KB, 70 views)
File Type: jpg IMG_2630.jpg (69.6 KB, 42 views)
File Type: jpg IMG_2631.jpg (39.4 KB, 58 views)
Reply With Quote
  #2  
Old 09-12-2017, 11:49 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,541
First rule of operating any vintage TV: never, ever leave one running unattended, especially a color set.
Reply With Quote
  #3  
Old 09-13-2017, 08:13 AM
Radiophile2001's Avatar
Radiophile2001 Radiophile2001 is offline
VideoKarma Member
 
Join Date: Jun 2006
Location: Montclair, VA
Posts: 105
I have certainly learned my lesson.....I heard some unusual buzzing sound while listening to an old AM radio....one I had never heard before in the sound of AM interference.....and I immediately suspected one of the TVs....
Reply With Quote
  #4  
Old 09-13-2017, 08:55 AM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 14,758
If it still has sound then it probably has B+ (if not check the B+ supply circuits).
Without the HV rectifier (3CU3) installed, and with the room dark does the Horizontal output tube plate (different from the heater which is supposed to glow) start to glow (red/orange)? If the plate stays dark that is good, but if the plate glows do NOT let it run for more than 1 minute (or damage to that expensive tube may result). If the tube plate glows (commonly called red plating), measure the grid bias. If the grid bias is somewhere around -50 to -75 volts DC then you have proper grid drive (if not the H oscillator needs work). look for shorts on the secondary side of the flyback.

Do you have the schematic for this set? If not look for the Sam's photofact for it. Schematics are essential for troubleshooting/finding your way around in a color TV.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
  #5  
Old 09-13-2017, 12:23 PM
Radiophile2001's Avatar
Radiophile2001 Radiophile2001 is offline
VideoKarma Member
 
Join Date: Jun 2006
Location: Montclair, VA
Posts: 105
Hi there--

I tried what you suggested, but unlike yesterday with the 3CU3A still removed, its connector was sparking like Frankenstein's lab....and making sparking noises. I turned it off soon thereafter. No smoke or anything. All other tubes looked like they were heating up.

I have attached a pic...the connector is circled in red. Also circled is one pin hole that oozed a little bit of oily stuff. It is also on that pin of the removed 3CU3A.

My problem--do not have a schematic and do not have any diagnostic gear. More of a hobby that a specialty for me. I can solder, replace tubes, wires, diodes, resistors, capacitors, etc, but most of all I am a TV idiot who is much better at restoring transistor radios.

Thanks again, though, I am willing to try to fix it as much as my skills will allow ;-)

I had this crated and shipped from the Chicago area years ago from one of the major collectors in this forum,...can't remember his name but he had a basement full of TVs and was a real pro at repairing 60s sets, along with Lawn Boy mowers!
Attached Images
File Type: jpg Sparks-Sylvania.jpg (80.1 KB, 54 views)

Last edited by Radiophile2001; 09-13-2017 at 12:30 PM.
Reply With Quote
Audiokarma
  #6  
Old 09-13-2017, 12:27 PM
Radiophile2001's Avatar
Radiophile2001 Radiophile2001 is offline
VideoKarma Member
 
Join Date: Jun 2006
Location: Montclair, VA
Posts: 105
Oh yeah -- also, the set still has full sound. I also have a new 3CU3A on the way from ebay....about $9 shipped.
Reply With Quote
  #7  
Old 09-13-2017, 01:08 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 14,758
If the top connector is creating a healthy arc like that then all the troubleshooting advice I gave is likely irrelevant. Try it with the old HV rect tube back in and see it it produces a raster. If not then you definitely need that tube you ordered. If it does produce a raster as bright as before with the old HV rect in it then there was some other issue that has it has temporarily recovered from.

There should not be anything in the pin of that tube socket to produce an oily substance...That oil is probably grease/dirt that found it's way into the set from outside. It is not bad (and sometimes necessary such as when dirt becomes a conductive path for arcing) to clean HV cage areas.

If you plan to fix the set your self/own it for the long haul you really should pick up a copy of the schematic/service data and keep it with the set.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
  #8  
Old 09-13-2017, 01:29 PM
zeno's Avatar
zeno zeno is offline
VideoKarma Member
 
Join Date: Mar 2013
Location: New Hampshire
Posts: 4,672
I am with Tom C. Discharge the CRT & pull off the anode lead.
Pull the 3CU3 socket & clean it with 91% isopropyl alcohol.
Clean all the wires to it & the "cup" also. Put back together with
the new 3CU3 & try it.
BTW dischage the CRT AGAIN before reassembly !
BTW #2 most HV rect tubes DO NOT have a filament glow !

73 Zeno
LFOD !
Reply With Quote
  #9  
Old 09-13-2017, 02:09 PM
Radiophile2001's Avatar
Radiophile2001 Radiophile2001 is offline
VideoKarma Member
 
Join Date: Jun 2006
Location: Montclair, VA
Posts: 105
Thanks--!!

I will take all of these steps when the new tube comes....figure I will try it with a good tube first....

Also, discharging the CRT--is that basically just turning on the set without it being plugged in before reassembling with new tube hookup?

Will QD electronic cleaner work as well as 91% alcohol? I have both.

Thx again
Reply With Quote
  #10  
Old 09-14-2017, 11:18 AM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,832
Quote:
Originally Posted by zeno View Post
I am with Tom C. Discharge the CRT & pull off the anode lead.
Pull the 3CU3 socket & clean it with 91% isopropyl alcohol.
Clean all the wires to it & the "cup" also. Put back together with
the new 3CU3 & try it.

BTW dischage the CRT AGAIN before reassembly !
BTW #2 most HV rect tubes DO NOT have a filament glow !

73 Zeno
LFOD !
I'd also clean the regulator socket and cap above the cage - it has full 25KV on it and looks as though it may be just as dirty, judging by the plate cap.

HV loves and attracts dirt - it's a much lower resistance/impedance and may be your only problem.
__________________
Brian
USN RET (Avionics / Cal)
CET- Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!

Last edited by Findm-Keepm; 09-29-2017 at 06:39 PM.
Reply With Quote
Audiokarma
  #11  
Old 09-15-2017, 04:45 PM
Radiophile2001's Avatar
Radiophile2001 Radiophile2001 is offline
VideoKarma Member
 
Join Date: Jun 2006
Location: Montclair, VA
Posts: 105
Quote:
Originally Posted by Findm-Keepm View Post
I'd also clean the regulator socket and cap above the cage - it has full 25KV on it and looks as though it may be just as dirty, judging by the plate cap.

HV loves and attracts dirt - it's a much lower resistance/impedance and may be your only problem.

Will do...thanks!
Reply With Quote
  #12  
Old 09-13-2017, 02:44 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 14,758
To discharge the CRT take a screwdriver with a well insulated handle connect it's metal shaft to the TV chassis with a clip lead and slip the blade of the driver under the HV connector on the top of the CRT bell until a spark is heard or you know your hitting the metal connector.
The best way is to use an HV probe instead of the screwdriver/jumper method, but I'd guess you don't have one (that is another important tool for TV work). Second best is to put a high value (meg ohm and up) resistor in series with the clip lead.
If you don't have a resistor (the HV probe has one inside) in series with the ground the stored HV will tend to bounce back within 30 sec to 1 min of discharge.

Failure to discharge the HV stored in the CRT may result in one heck of a nasty static jolt.

Alcohol is best for HV cages/hardware. If you want to use the cleaner on the socket electrical contacts it should not hurt there.

The guy you got the set from is probably Doug Harland DRH4683 is his handle here and on you tube. Nice person I've bought stuff from him too.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
  #13  
Old 09-13-2017, 03:06 PM
Radiophile2001's Avatar
Radiophile2001 Radiophile2001 is offline
VideoKarma Member
 
Join Date: Jun 2006
Location: Montclair, VA
Posts: 105
I will follow these instructions....thanks....! (don't need to damage the thing any more than it is)

Yes, Doug was his name and he was nice enough to give me the set....just as long as it made it to a good home that would not trash it. It has lasted a long time.

The same kind of thing had happened to my Zenith 1968 color TV.....but that involved much more smoke and melting. I was in the room for that one. All I did is turn it on, with the others.

Amazing how ghosts get in these machines! ;-)
Reply With Quote
  #14  
Old 09-13-2017, 03:58 PM
DavGoodlin's Avatar
DavGoodlin DavGoodlin is offline
Motorola Minion
 
Join Date: Aug 2011
Location: near Strasburg PA
Posts: 3,400
Ill look up CF16W/DO9 issues in my book but PM me with your personal email and I will scan you the schematic. The 3CU3 should have you back up but take all the good advice here on cleaning things.
__________________
"When resistors increase in value, they're worthless"
-Dave G
Reply With Quote
  #15  
Old 09-14-2017, 10:46 AM
Radiophile2001's Avatar
Radiophile2001 Radiophile2001 is offline
VideoKarma Member
 
Join Date: Jun 2006
Location: Montclair, VA
Posts: 105
Sure, it's sent, thx

Last edited by Radiophile2001; 09-14-2017 at 10:49 AM.
Reply With Quote
Audiokarma
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:35 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.