Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early Television Foundation CRT Rebuilding Project

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 06-09-2018, 10:45 AM
Chip Chester Chip Chester is offline
VideoKarma Member
 
Join Date: Apr 2012
Posts: 605
Trash or treasure?

Found the item below in the weeds while cleaning up back lot at ETF.
Looks like a cam for a timer switch, or maybe an emoji stencil. Or perhaps I've found Nemo.
It was in the area where CRT ovens were scrapped out (by others).

http://videokarma.org/attachment.php...1&d=1528559274
Attached Images
File Type: jpg IMG_7539.jpg (87.9 KB, 61 views)
Reply With Quote
  #2  
Old 06-09-2018, 06:42 PM
MadMan's Avatar
MadMan MadMan is offline
'A Disgusting Brony'
 
Join Date: Oct 2016
Location: Chicago
Posts: 638
It looks about 3 inch in diameter, that right? Looks like a miniature painter's palette. Possibly an electrical insulator for something. Is it flimsy or solid?
Reply With Quote
  #3  
Old 06-09-2018, 07:05 PM
Celt's Avatar
Celt Celt is offline
Peanut Head
 
Join Date: Nov 2002
Location: Paragould, Arkansas
Posts: 1,662
It's a ghost of Pac Man...
__________________

Let me live in the house beside the road and be a friend to man.
Reply With Quote
  #4  
Old 06-09-2018, 09:51 PM
Chip Chester Chip Chester is offline
VideoKarma Member
 
Join Date: Apr 2012
Posts: 605
5.5" at widest point; approx. 1/16" plexi. 1/2" hole. Stiff, not flimsy.
Celt, you may be close, but it doesn't make any 'wocka-wocka' sounds. At least not yet.
I'd be happy to put it back inside the warehouse, but I'll wait until someone chooses a specific destination, so it doesn't get lost.
That destination could well be the dumpster, of course...
Reply With Quote
  #5  
Old 06-12-2018, 10:49 PM
ohohyodafarted's Avatar
ohohyodafarted ohohyodafarted is offline
Bob Galanter
 
Join Date: Sep 2005
Location: Whitefish Bay, Wi (Milwaukee)
Posts: 970
The item you are looking at is the special cam that was used in the controller for processing the long 6 hour pump down for 15GP22 crt's. It goes in the Partlow chart recorder temperature controller timer that controlled Hawkeye's oven temperature ramp up and cool down cycle.

The Partlow ramp controller has a clock timer that does 1 revolution per 3 hours. The cam rotates with a cam follower on the edge of the cam. AS the cam follower rides further and further away from the center of the cam, the temperature increases. At the 3 hour mark, the cam is removed and flipped over, and the cycle reverses. The second 3 hour period eventually goes into a cool down period toward the end of the cycle.

The Partlow ramp controller had a temperature sensing element consisting of a long stainless steel tube with a metal reservoir bulb at the end which sat inside the oven to sense the actual temperature. The stainles steel bulb and the tubing were filled with mercury. The end of the temperature sensor that was connected to the bottom of the Partlow ramp controller had a piston inside it. AS the temperature increased in the oven, the mercury expanded which pushed against the piston in the end connected to the Partlow controller. The moving piston pushed against a mechanism that compared the position of the cam follower, to the temperature that was being sensed by the mercury element. If the cam follower said we should be at 300 degrees and the sensor detected only 290 degrees, the Partlow controller would trip a micro switch which energized the gas valve and the gas burners would ignite. Similarly when the temperature was higher than the cam follower wanted, the micro switch would open and the burners would extinguish.

By plotting the ramp of the cam, you could control the rise and fall of the temperature of the oven as fast or slow as you wanted. IN addition there was a circular chart recorder in the Partlow ramp controller that actually had a pen that tracked the actual course of the temperature over the 3 hour period.

It was old school, but it is what we had back in the day and it worked very well. Sad to here that the Hawkey oven has been scrapped. There was a lot of good usable (although old) technology in that oven. I hope at least the usable components were saved.

This photo shows the Partlow processing controller with one of the plastic cams installed.
Attached Images
File Type: jpg image023.jpg (24.8 KB, 6 views)
__________________
Vacuum tubes are used in Wisconsin to help heat your house.

New Web Site under developement
ME http://AntiqueTvGuy.com

Last edited by ohohyodafarted; 06-20-2018 at 11:52 PM.
Reply With Quote
Audiokarma
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:11 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
ęCopyright 2012 VideoKarma.org, All rights reserved.