[ohohyodafarted]

RE: Beltron,

I just wanted to relate an experience I had with a 21cyp22. Upon testing it with a B&K 465 crt tester, the tube was devoid of all emission. I had very little hope of bringing the tube back to life.

I hooked up the Beltron and set the filiment voltage at 6.3 as normal. I waited for 10 minutes and only the green gun moved just a tad to about 10% of full scale. The red and blue showed no signs of life at all. I figured this tube was a gone'r.

I next moved on to the cleaning procedure. IN this mode the Beltron is used to "wake up" a sleepy tube. The procedure is to boost filiment voltage to 12 or 13 volts and let it cook for about 20 seconds. Once again no luck on any of the guns.

Well at this point there seemed to be very little hope that this tube could be saved So I proceeded to the restoration stage were the Beltron removes surface grunge from the cathode material to expose good material,( provided there is still good cathode material to expose.)

I raised the filiment voltage to 13v, and As normally happens the 2 large blue pilot lights flickered and blinked, I processed each gun as recommended for 3 cycles. As I processed each gun the emission got up to about 97% of full scale. I was very encouraged..

When I went back to test mode all 3 guns were now between 95% and 97% of full scale.

Now for the real test. I removed the Beltron and went back to the B&K 465 tester. I like this tester for a more accurate measurement because it has a nice large 4" meter and it seems to give a better quantitive measurement of the emission than the Beltron does. The scale is calibrated from 0 to 1000 where 200 is the cutoff for good and bad. If I get a reading of over 500 and 10 seconds life with this tester I know I have a very good tube.

I set the cutoff bias and proceeded to test each gun. I was ellated to find that each gun tested between 650 and 750 and had a life test of 16 seconds on the weakest gun. I have rarely ever tested a tube that went over 800 on the B&K, not even new tubes.

Absolutely incredible for a tube that was for all practical purposes totally dead on first testing.

It is my opinion that even if a tube can be awakened through boosting filiment voltage, or just opperating for an extended period, that in itself is not enough to bring the tube back to optimum performance, because you are still trying to boil off electrons from behind a dead layer of cathode material. Sort of like trying to piss through a window screen. The Beltron not only awakens the cathode, it actually has an ability to microscopically re-expose the cathode face so that it will once again emit a proper flow of electrons. A meer awakening of the cathode will not produce an equivalent result.

I have used the Belton on 50 or more tubes since I got the unit several years ago, and in some cases the crt is just plain dead due to lack of cathode material remaining. But if there is still viable cathode material available, the Beltron can exposed the material and bring back nearly full performance to a tube that was otherwise for all practical purposes, dead. And I have never damaged a tube with the Beltron. I can't say that about the B&K. I zapped the filiments on two 10BP4's with the 465 trying to rejuvenate them before I bought my Beltron. Now I only use the B&K for emission testing.

IF this 15GP22 still has a good vacuum, and the tube has weak emission, it is very likely that it can be brought back to very good performance with the Beltron. When you get the chassis up and running, see if someone in your area has a Beltron that could come over and test and possibly clean or restore your tube. You will need to build a 20 pin to 14 pin adapter to use the Beltron 14 pin socket. It can't hurt and it will possibly restore the tube to a very good performance level. At the very least it will improve it.

Good Luck and keep us posted on your progress.