|
|
|
|
|
#1
11-11-2007, 12:59 PM
|
||||
|
||||
|
Will CRT rebuilders disappear in near future?
Can anyone speculate on the availablility of CRT rebuilding services in the future? It seems like it is getting to the point where new CRT-based devices are not being used in commercial applications and probably old TV enthusiasts will constitute the great majority of CRT-rebuild needs (and this amount may not be enough to sustain a commercial business rebuilding CRT's)
Just wonder if I should try and get round CRT's rebuilt now rather than wait to do it in case the service becomes unavailable. 
|
|
#2
11-11-2007, 01:17 PM
|
||||
|
||||
|
Well I feel the same way about this. If CRT companies do go under, we should pool together, buy thier equipment and repair our own CRT's! Hech, I have a huge building out here I would gladly have the equipment sit at and operate!
__________________
Honey, turn on the tv.. I'm cold!
|
|
#4
11-11-2007, 03:04 PM
|
||||
|
||||
|
I too am afraid that the CRT rebuilders will go under due to lack of business. Due to the cheapness of recent consumer CRT sets; no one is going to have the CRT changed in one. That fact along with everything going to LCD, Plasma, etc. will probably hurt the CRT rebuilding market. Our local parts house recently discarded a bunch of new CRT's that have been sitting there for years. The owner told me that they had tried to sell them for below what they cost the supply house with no luck. They finally discarded them and wrote them off because they were taking up too much room. He said the only one's that bought CRT's were the hospitals for use in their TV's. Since those hospital TV's were different from consumer TV's, I guess it was cost effective to replace the CRT when it failed. After all, you can't buy those sets for $99.99 at wal-mart. BTW, there are some hospital TV's around here that are still used after 20+ years. I guess they keep them going as long as they can. I wonder if there's any of those old '70's Sylvania GT Matic hospital sets still in use anywhere. Those were the ones with the motorized tuner and the UHF position turned the set off.
|
|
#5
11-11-2007, 04:48 PM
|
||||
|
||||
|
Besides meeting electrical safety and medical device non-interference requirements, I'd bet that many hospital sets were purchased as part of a package including the intercom etc. So, when the room is upgraded to a complete new system, the TV gets replaced - and in the future, that will be flat panel.
|
| Audiokarma |
|
#6
11-11-2007, 05:04 PM
|
||||
|
||||
|
Law of supply and demand
Unless these guys are doing this part-time, I don't think rebuilding crt's would be a full time venture. It may take one of us the find the equipment necessary to rebuild these jewels of the past.
__________________
[IMG]
|
|
#7
11-11-2007, 10:33 PM
|
||||
|
||||
|
I wonder if the military has CRT's rebuilt?
__________________
This device isn't a spaceship, it's a time machine. It goes backwards, and forwards... it takes us to a place where we ache to go again.
|
|
#8
11-12-2007, 01:47 PM
|
||||
|
||||
|
Viva MEXICO!
I have the feeling that for many years after they stop doing it here, it will continue south of the border. Many of the rebuilders in Los Angeles (Dunbar, Pacificc Vacuum Sales, West Coast, and others,) sold their equipment to Mexican CRT companies when they went out of business. Charles
__________________
Collecting & restoring TVs in Los Angeles since age 10
|
|
#9
11-12-2007, 06:03 PM
|
||||
|
||||
|
Perhaps they are also doing it China. A recent thread of mine about a cheap Chinese set I found with a used VGA CRT in it turned up various listings for Chinese wholesalers offering "B" grade CRTs. Since then I have seen one more cheap Chinese set that had a CRT that looked older than the rest of the set (the corners were more rounded than recent CRTs). Though I doubt they will be doing anything with delta gun/round CRTs.
|
|
#10
11-13-2007, 10:56 AM
|
||||
|
||||
|
There is a popular bumper rechroming company called Bumper Boyz. They seem to be out of California but I strongly suspect the work is done south of the border. I can't imagine CA, with its strict enviromental laws, being a good place to set up shop, and these guys have low prices. I called them once and the woman who answered spoke hardly any English. I could see a similiar arrangement for crt rebuilding, assuming the quality control was up to snuff.
__________________
Bryan
|
| Audiokarma |
|
#11
11-24-2007, 07:39 AM
|
||||
|
||||
|
Quote:
__________________
From Captain Video, 1/4/2007 "It seems that Italian people are very prone to preserve antique stuff."
|
|
#12
11-24-2007, 12:04 PM
|
||||
|
||||
|
Quote:
I know that company... They have booths at all the car swapmeets. I agree 100% that they, and most other chrome dealers, have the work done in Mexico. Their US locations are just offices and warehouses. A few do replate here in CA, but the cost is about double. Most of the reproduction bumpers for popular cars & trucks (Mustangs, F-100s, 55-7 Chevys, etc etc) comes from China. This brings up an interesting concept: I bet there are more TVs total using 10BP4s than there are '55-57 Chevys. So with that logic, maybe it WOULD pay for a Chinese company to make 10BP4s. Charles
__________________
Collecting & restoring TVs in Los Angeles since age 10
|
|
#14
11-23-2007, 02:42 AM
|
||||
|
||||
|
I don't forsee any long term future for rebuilding conventional CRT displays. It's doubtful that many countries would have any sustained interest because of the rapid advances in LCD and Plasma display technology. Places like Asia, China, even Mexico, are currently where flat screens devices are being manufactured - so why would they bother with CRT repair, in the long run? It would seem to be uneconomical for small or large business. Perhaps the best hope would be for a niche player - someone with the expertise, equipment, and facilities integrated into some other venue to absorb the costs - essentially doing it as a contribution to television history.
|
 |
|
|
Hybrid Mode
